Aeropassion's homepage
Aeropassion's parteners :
Posted by Dan 
I am running windows XP.

I have tried them all and they all have the 'wrong' enable signal... (Only vista and windows 7 dll gets error popup ... in french...;(

Willing to try anything you have....

Thanks !!!!

-Doron.
Re: Jeducut with TB6560 4axis cnc board - if possible
March 03, 2012 08:44PM
Do you try CnCnet_xp.dll and after that visualCNC_xp.dll ?

Can you explain what is "the wrong enable signal" ? Are you talking about the clock of each motors or the general "enable" signals for the board ?

Jerome
Re: Jeducut with TB6560 4axis cnc board - if possible
March 03, 2012 11:55PM
I tried all the dll's and none works.

The only DLL that seems to 'almost' work is the CncNet_win_XP_Vista bit it gets an error popup... see attached file.

When I tell it to do a long movement with the CncNet_win_XP_Vista, ignore the popup error and then use the parallel port monitor and toggle pin 1 (general enable signal)... the motor move.

In any case, the general 'enable' signal is always the opposite of what this board needs.

See controller doc here : http://wenku.baidu.com/view/f6342ad049649b6648d747b4.html

So can I try next. do you have these DLL's with ability to change the polarity

-Doron.
Attachments:
open | download - jedicut.jpg (179.3 KB)
Re: Jeducut with TB6560 4axis cnc board - if possible
March 05, 2012 09:55PM
Hello,

You can try this dll. I inverted the general enable signal as you like. I will answer your other messages tomorrow.

Jerome
Attachments:
open | download - CncNet_XP.zip (47.8 KB)
Re: Jeducut with TB6560 4axis cnc board - if possible
March 06, 2012 02:51AM
the signal is has not changed ... sad smiley

Also you can see with this utility http://www.geekhideout.com/parmon.shtml

I now know that pin one (1) needs to be high (and not low as I thought).

I defined Engine on/off as pin 1 in the GUI but according to Parmon software nothing change.... (When Mach3 runs... that pin is green)

I am not sure you are sending the data to that pin.


-Doron
Re: Jeducut with TB6560 4axis cnc board - if possible
March 06, 2012 07:51AM
Tell me exactly what you want because I have difficulties to understand.

pin 1 for general Enable signals.
High level signal to enable your board.
Low level signal (0) to unable your board.

Is it right ?

Yesterday I did a quick modification on cncnet_xp.dll to invert high and low level on this signal. Are you sure that you use the dll I posted before and that you choose it in Jedicut's settings ?

Jerome
Re: Jeducut with TB6560 4axis cnc board - if possible
March 06, 2012 04:17PM
Jerome,

1) Yes I am sure I put the the new DLL in that directory and slected it. (I renamed the old one to cncnet_xp_old.dll and it showed in the gui menu as cncnet_xp_old.dll)
2) Did you try the Parmon utility on your computer ? On my machine it does not look like you are stetting the motor enable pin to high on ANY of the dll's (I told it it is pin 1 on the DB-25)
3) You can see here : http://wenku.baidu.com/view/f6342ad049649b6648d747b4.html the mach3 settings that my board is using and when I use mach3 is moves just fine.

Thanks !!!!

-Doron
Jerome!

Please develop some kind of solution! please+please+please!!!!!!!!!!!!!!!!!!! smileys with beer
Re: Jeducut with TB6560 4axis cnc board - if possible
May 04, 2012 12:46PM
Hello,

I'm sorry but don't know what to do and I don't have this board. May be you can contribute together and offer me this board ? winking smiley Without the board, It's to difficult to work, and It needs too time.

Do you try rob's settings ?

Jerome
till not, but if i can help on this project please contact with me.

Ambass
Re: Jeducut with TB6560 4axis cnc board - if possible
May 13, 2012 08:52AM
Hello,

Can you try this new plugin ? I inverted the general enable signal.

After you try, can you indicate the configuration of parallel port in Jedicut ?

Jerome
Attachments:
open | download - CncNet_XP_TB6560.zip (47.8 KB)
Tomorrow i'll test it! Thank's!
Nothing to do... sad smiley

My setup:


Re: Jeducut with TB6560 4axis cnc board - if possible
May 16, 2012 12:57PM
Hello,

Do you have an external timer on your CNC board ?

If not, it's normal that you don't check the check with the label "Synchronize with external timer" (on your second screenshot in another language).

With this configuration, you can't use speed values like "4" or "10". You must use speed value like 10000000. If it's to slow, try to remove one zero, or divide this value by 2. Step by step, you must adjust your speed value.

If you never see one step done by your motor, there is another problem.

Jerome
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
May 16, 2012 08:46PM
Ambass

Have you made a parallel crossover lead between the pc parallel output and the parallel input of the TB6560.
The connections are on the last post first page of this subject.
My setup has been working for over a year now with no problems.
I will list all of my jedicut settings here when I return home and check my workshop computer.

Rob
Hi Jerome!
I was tried your suggestions, but it doesn't work. nothing to do...

RoB!

Waiting four your settings!!!!

Thanks
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
May 21, 2012 08:38PM
I,ve been away for a few days. Here are my settings.

Control card TB6560 switch 5 on all other switches off.

Communication:
Active Table------Default
Mode-------VisualCNC_xp.dll

Engines Clock Dir

x1 8 9
x2 4 5
y1 6 7
y2 2 3

Ex Timer 10 Heating 16
Engine on/off 17 11
12

Syn engine rot-------off (no tick)

X1,X2,Y1,Y2 All the same: Nb mm/pas 0.0025 (this is for my 6mm treaded drives)
Cut Speed 50 (0.19mm/s)
Fast Speed 15 (0.59mm/s)

No heating control (no tick)

Hope this helps good luck. Rob
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
May 21, 2012 08:49PM
Ex Timer 10
engine on/off 17
Heating 16
Return pin 11
Status 12

Did not attach correctly
Today may will test it's! Thanks!
today is the day... shock smiley but this machine didn't want to work... nothing to do.

BUT! Today i was received a USB-paralell cable. i'll test with it...
Hi!

Today i was cutted the original paralell cable with give for the board. I went to buy another one, but not working with this board. Somebody can help on me with original or working paralell cable pinout?!

Thanks a lot!

Ambass
problem solved! But the jedi dont want to work... BUT! I have a paralell switch and without the machine dont work. witch tipe of paralell do you use in bios setup?!
Re: Jeducut with TB6560 4axis cnc board - if possible
June 24, 2012 09:51PM
Good evening.

We had this same problem this WE. As I explained in an other post on the french forum, we had to replace the motors on our CNC, and we needed also to replace the driver, our old driver was not able to manage bipolar motors.

We bought a TB6560 driver and 4 NEMA 17 motors 200 steps / revolution (instead NEAM 17 100 steps motors), and as explained above, it was impossible to rotate them.

I just received a mail from one of my collegue who succeeded to run the motors.

It seems that the problem is due to differences between configuration of the LPT1 parallel port pin configuration and the TB6560 pin configuration. I don't have any supplemental information for the moment, we will install everything on our CNC on next saturday.

I will measure the speeds on all axis to compare them with the speeds estimated by Jedicut, it was my problem just before we changed everything.

Manu
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
June 25, 2012 08:49AM
Here are the connections required for the parallel lead you have to make to get the TB6560 to work correctly.

Rob
Attachments:
open | download - connections.GIF (4.5 KB)
hi rob

i not understand pin10 timer input?

your mean /make external timer bord right?

please sample external timer bord
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
November 12, 2012 09:52AM
Bo

Pin 10 is the PC timer output you can make a timer if you wish I do not use one.

You can make a timer using a 555 ic.

Rob
Re: Jeducut with TB6560 4axis cnc board - if possible
November 13, 2012 07:07AM
Hello rob,

Do you have a simple schema to share ? Many people have this question :/

Jerome
rob
Re: Jeducut with TB6560 4axis cnc board - if possible
November 13, 2012 07:45PM
Here is a small timer circuit that can be constructed on a vero board. (copper strip board)
hope it helps there is a link for working out the Freq: output.

Rob
Attachments:
open | download - 555 timer.JPG (23.1 KB)
Re: Jeducut with TB6560 4axis cnc board - if possible
November 14, 2012 01:06PM
Thanks winking smiley

Jerome
Sorry, only registered users may post in this forum.

Click here to login



Aeropassion

Paris en photo | Design by Le Flaketou, création de site internet

Phorum